Mon-Fri: 7AM-8PM, Sat: 8AM-6PM, Sun: 9AM-5PM Licensed & Insured [email protected] Serving Junction, TX

Screw Drive Opener Repair in Junction, TX

Screw-drive openers cleaned, lubricated and repaired. Typical cost $125-$350.

From the first phone call to the final safety test, screw drive opener repair in Junction, TX follows a simple process: diagnose, quote, repair, test. Screw-drive openers cleaned, lubricated and repaired.

Is it time for screw drive opener repair?

  • The motor runs but the door doesn't move
  • Squealing from the rail
  • Slow or jerky travel, especially in cold weather

Why this happens

  • Worn trolley or coupler
  • Dry or dirty screw rail
  • Temperature swings affecting the rail

Before the technician arrives

  • Look for grime and dried grease along the threaded rod.
  • Only use the lubricant the manufacturer recommends for the screw rail.

Still stuck? Our free symptom checker and troubleshooting wizard walk you through it step by step.

What happens during the visit

  1. Inspect the screw, trolley and motor coupler
  2. Clean and lubricate the rail
  3. Replace worn trolley or coupler parts
  4. Set the limits and force
  5. Test the opener

Screw Drive Opener Repair cost in Junction, TX

$125-$350Typical range, parts & labor
about 1 hourTypical time on site

What moves the price:

  • Drive type: chain, belt, screw or wall-mount
  • Whether the fix is a part or a whole new opener
  • Remotes, keypads and smart accessories
  • Ceiling height and rail extensions

These are typical U.S. ranges, not a quote. You get an exact price for your door before any work starts. For a quick estimate, try the repair cost calculator.

Screw Drive Opener Repair in Junction, TX

A closed garage in a Texas summer gets very hot, which shortens the life of opener circuit boards, capacitors and photo-eye sensors. Storms add power surges, so a surge protector is cheap insurance.

Technicians serve all of Junction (ZIP code 76849), plus Mason (36.8 mi), Kerrville (48.5 mi), Eden (50.4 mi) and Brady (51.6 mi). Call (833) 435-8883 to book a visit in Junction.

Screw Drive Opener Repair: frequently asked questions

How much does screw drive opener repair cost in Junction, TX?

Screw Drive Opener Repair typically costs $125-$350 including parts and labor, and usually takes about 1 hour. The exact price depends on your door and the parts it needs, and you get it before any work starts. Call (833) 435-8883 for a quote.

Can you do screw drive opener repair the same day?

Often, yes. When a technician is available we can usually come the same day, and common parts are carried on the truck. Doors that won't close or have a broken spring are treated as priority calls, and emergency service is available.

Is screw drive opener repair covered by a warranty?

Our work comes with a 90-day labor warranty on repairs. New parts and doors also carry the manufacturer's warranty. Ask for the warranty details in writing with your quote.

Are your technicians licensed and insured?

Our technicians are insured, and where Texas or Junction requires a contractor license for garage door work, the job is done under that license. You're welcome to ask for proof when you book.

Should I repair or replace my opener?

A good rule of thumb: if the repair costs more than about 50% of a replacement, or the opener is near the end of its life, replace it. Most openers last 10 to 15 years. If yours is older than that, lacks photo eyes or rolling-code security, or needs a logic board or motor, a new opener is often better value. Springs are the exception: a broken spring is always replaced, never repaired. Our free repair vs. replace calculator can help you compare.

More services

Popular Garage Door Services in Junction, TX

Skylink Opener Gear & Sprocket Replacement

Skylink makes openers and a wide range of universal replacement remotes and keypads.

Typical $125-$275

Overhead Door Off-Track Garage Door Repair

Overhead Door traces its roots to C.G. Johnson, who invented the upward-acting garage door in 1921. The company builds residential and commercial doors and openers.

Typical $175-$450

Hörmann Garage Door Roller Replacement

Hörmann is a German manufacturer of residential and commercial doors and openers with North American operations.

Typical $150-$350

Raynor Torsion Spring Replacement

Raynor, based in Dixon, Illinois, makes residential and commercial garage doors as well as openers.

Typical $200-$450

Steel Garage Door Repair

Dents, rust and bent sections on steel doors repaired or replaced.

Typical $150-$600

Hörmann Garage Door Opener Repair

Openers that hum, click, reverse or won't respond, diagnosed and repaired.

Typical $125-$350

Cornell Cookson Commercial Door Operator Repair

Cornell Cookson makes rolling steel service doors, security grilles and rolling fire doors.

Typical $300-$1,200

CHI Overhead Doors Garage Door Track Repair

CHI Overhead Doors builds residential and commercial sectional doors in Arthur, Illinois, and sells them through independent dealers.

Typical $150-$400

Sommer Opener Gear & Sprocket Replacement

Sommer openers, made in Germany, put the motor on a carriage that travels along the rail instead of hanging from the ceiling, so servicing them is a little different from a conventional opener.

Typical $125-$275

Garage Door Tune-Up & Maintenance

A full inspection, lubrication and adjustment to prevent breakdowns.

Typical $90-$200

Raynor Opener Gear & Sprocket Replacement

Stripped drive gears replaced so the motor moves the door again.

Typical $125-$275

CHI Overhead Doors Extension Spring Replacement

CHI Overhead Doors builds residential and commercial sectional doors in Arthur, Illinois, and sells them through independent dealers.

Typical $150-$350

Garage door stuck, noisy or broken?

Talk to a garage door technician in Junction, TX now. Tell us what the door is doing and we'll give you a price and an arrival window.

Call NowFree Quote